We have several metric metal working charts for press brakes, shear, hole punching, metric conversion charts, metric to US conversion charts. What I can't find is a table of rod size vs thread size. Brockwood, you are referring to a Tailstock Die Holder - useful tool. I was able to get it done by properly supporting the rod along the entire length that stuck out of the left side of the spindle. Both ends of a shaft are 8mm threaded, one is 8x1 and the other is 8x1.5.

So besides #5 (1/8" rod) nothing under 1/4" seems to be a standard off-the-shelf rod size. No problem on a 4" piece of stock, but I have needed to do it to an 8 foot piece of 1/4" stock, for instance.

99. I mistook harbor freight dies for dies that actually can cut carbon metal. Yes it won't be a problem as long as that imperial size rod is the right size and won't snap your die. $14.99 $ 14. With Mikey s example there is just about .008" difference on the nominal diameter and less than .004" tolerance on the pitch diameter. Fitting A Die Step 1 Back the locking screws off of the die.

Thanks for the chart Mikey. It would seem to be easy, just take a die and cut the thread.

You must log in or register to reply here.

... has 16 threads per inch and the tap drill size is 5/16 inch. So the rod needs to be turned down a little to the correct size for an easy to thread size. General background and Pre-checks. It would seem to be easy, just take a die and cut the thread. Brockwood, you are referring to a Tailstock Die Holder - useful tool.

What size do I turn the threaded parts to before threading? by KMIAN TOOLS.

But it is not usually that easy, because the rod is too big to cut a thread on it with a die, as it it a bit too large and can jam up and break something if you try to force it. Drill America Carbon Steel Hex Threading Die (#4-40 - 5"-8, m1.6x.35 - m50x1.5, Standard and Left Hand) Bright Finish, DWT Series. You are giving him drill holes sizes for a tapped hole.Compare that hassle against finding the right threaded rod. How convenient 4.4 out of 5 stars 30. I can find an amazing number of tables of tap drill size vs thread tap. We just need to deal with it the best we can.Drill rod is another product I use to meet Enco minimumsHumor- i found the main problem. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register. Check your pitch diameter before your final cut. Another issue with all this is getting the die not wander away from 'true'. I know this seems incredibly basic but I can't figure out the answer what is the proper size that you're Metal rod has to be for the die you want to use.Here is a table that will tell you what you need to know. M4, for example, means the "standard" M4 thread size: for a bolt, the outside of the thread would be 4mm in diameter, and the spacing between threads (the pitch) would be 0.70mm.

A typical bolt thread is cut at somewhere around 65% of a full thread, which is much easier to cut, and is about 90% as strong.The size rod you will need is the major diameter of the thread you will be cutting with the die.

Once I get my BXA tool holders to fit my lathe: I'm making die feeders (sorry can't think of their proper name). This chart gives the metric tap size in inches , millimeter diameter, thread count, thread pitch and tap drill size … Place the rod or other item that you wish to thread into the center hole of the split ring die… But it is not usually that easy, because the rod is too big to cut a thread on it with a die, as it it a bit too large and can jam up and break something if you try to force it. Copyright ©1999 - 2019, North American Subaru Impreza Owners Club, Inc. Determine which thread size you wish to cut; Metric threads, M4, M5, M6, M8, M10 & M12 are commonly used.

all I can find is standard size rods at hardware stores Yes it won't be a problem as long as that imperial size rod is the right size and won't snap your die.^ Any rod between 27/64th's and 7/16's should be fine, taper the rod end abit before passing the die and use the right tapping oil for the material and you'll be set.^ Any rod between 27/64th's and 7/16's should be fine, taper the rod end abit before passing the die and use the right tapping oil for the material and you'll be set.Compare that hassle against finding the right threaded rod.You got it all wrong.

So 11/32 imperial rod is fine to be threaded by a 10mmx1.5 die. It was a good thing I placed the lathe with this in mind. For example, suppose I wanted to make a 1/4-20 thread on the end of a piece of metal or plastic rod.

There are also calculators online. FREE Shipping on eligible orders.

I have an old machinery's handbook with a 1948 copyright date and couldn't find it in there either. I'm making a part for the lathe.